WOODRIVER Socket Chisel 1/8″

WOODRIVER Socket Chisel 1/8″, 161641, Forged from 100 CR-V steel. This alloy holds an edge that is also impact resistant., Factory-ground 25° bevel, Tempered in salt bath to HRC58-63, 1/8″ Wide Blade length is 4″; Overall length is 9-5/8″ to 9-7/8″, The WoodRiver Bevel Edge Socket Chisel, the transition from the “flat” of the back to the socket was developed with a gradual slope. This avoids the back of the chisel from suddenly lifting on longer paring operations. The side bevels sweep back towards the centerline, allowing the chisel access to tight corners, which is imperative for dovetail work. The resulting flat area or “land” is a consistent 0.7mm – narrow enough for tight access but wide enough to prevent an troublesome sharp edge. The complete tool is designed with balance in mind to.

Triple Reed 1/8″ Cutting Iron for Recod No. 405 Plane- Unused- mjdtoolparts

An old hardware stock TRIPLE REEDING CUTTING IRON by the Record Tool Works, Sheffield, England. This cutter, which will fit the Record No. 405 combination plane as well as the Stanley No. 45 and No. 55 planes, cuts three parallel 1/8″ reeds. It is in unused condition. This cutting iron is designed to fit the Record No. 405 plane, but it will work with the Stanley No. 45 and No. 55 combination planes, and it will also work in the Record No. 405 combination plane produced by the Record Tool Works of Sheffield, England and the Veritas Large Combination Plane produced by Lee Valley Tools of Ottawa, Ontario, Canada. This example is in excellent condition and could be put directly to use. Length = 3.50 Inches (Ref. Id No.: 344512) [Free Shipping]

.S. Osborne Caning Chisel #405, Size 1/8″ Made in USA

S. Osborne Caning Chisel. The specially designed tool for removing old spline from chairs. Hardened and tempered steel. Has a translucent cellulose acetate handle. Made in USA. Width of point : 1/8″ Blade length : 4″ Overall length : 8″.

Caning Chisel #405, Size 1/8 Made in USA

Caning Chisel. The specially designed tool for removing old spline from chairs. Hardened and tempered steel. Has a translucent cellulose acetate handle. Made in USA. Width of point : 1/8″ Blade length : 4″ Overall length : 8″.

Craftsman 41594 WF USA 1/8″ Slotted Screwdriver Sears Best 1980’s Era Very Nice

The Craftsman 41594 WF USA 1/8″ Slotted Screwdriver is a vintage original tool from the 1980’s era, manufactured in the United States. This collectible item is a part of the Sears Best line and is highly sought after by woodworking enthusiasts and collectors alike. With its classic design and quality craftsmanship, this screwdriver is a valuable addition to any tool collection.

Orig. Cutter for Stanley No. 248 – 1/8″ Size- Notched Rectangle- mjdtoolparts

An ORIGINAL 1/8″ WIDTH CUTTING IRON for a Stanley No. 248 weatherstrip plow plane by STANLEY. This cutter is in excellent condition. It is marked with the Notched Rectangle trademark introduced in the 1930’s as well as the size designation. It could be put directly to use if the purchaser chooses. Length = 2.50 Inches (Ref. Id No.: 396637) [Free Shipping]

IRWIN Marples Chisel for Woodworking, 1/8-Inch (3Mm) (M44418N)

High carbon solid-forged hardened steel blade for superior performance and maximum edge retention. These wood chisels are designed for use with a wooden mallet or the palm of the hand. IRWIN Tools Marples chisels have been the industry leader for woodworkers for nearly 200 years.